Kategorie: Kenwood TS-480HX MARS MOD

Kenwood TS-480 + mAT-125E

Was für ein schöner Morgen nach dem heftigen Schneefall gestern, aber sehr sehr kalt bei -9C am Morgen. Ich habe meinen POTA Termin kurzerhand gestrichen. Trotz meiner neuen Standheizung im Auto ist es mir zu kalt draussen eine Antenne aufzubauen. Vielleicht liegt es auch eher daran, das meine Frau mir ein Raclette auf den Mittag versprochen hat. Da sollte und kann man nicht nein sagen…

Kaltes Wetter

Es gibt auch zu Hause im Shack immer etwas zu tun, ich dachte mir ich pack mal wieder das sehr tolle Kenwood TS-480HX aus. Das Gerät mag ich sehr und konnte das in einem tolle Setup übernehmen. Der Empfänger und die Filter sprechen noch heute für sich. Warum bei einer nächsten Aktivierung nicht einmal dieses Gerät mitnehmen? Eigentlich wäre mir das TS-480SAT ja lieber, mir fehlt im HX der eingebaute Tuner und die 200 Watt Sendeleistung benötige ich nie. Die 100 Watt des TS-480SAT würden mir reichen, wenn jemand ein SAT hat und das gegen den HX tauschen will… sofort bei mir melden.

Da ich jetzt im Moment mit dem HX leben muss, frage ich mich welcher Tuner da mit ins Gepäck könnte. Schnell bin ich auf den mAT-125H in meinem “Lager” gestossen. Der 125H eignet sich leider gar nicht mit dem IC-705 zusammen. Beim TS-480 kann man die Taste PF mit einem Tunesignal belegen. Sehr praktisch, es sendet dann mit 10 Watt ein CW Dauersignal. Den mAT-125H habe ich in den automatischen Modus versetzt, sobald ein Signal ankommt wird das SWR geprüft und bei Bedarf der Tunevorgang ausgelöst. Sehr wichtig so eine Tune Taste zu haben, wir vom HB9AF haben da schon viel darüber diskutiert und wissen ohne die Taste geht das funken nicht.!

PF Taste TS-480HX

Somit ist das Setup TS-480HX und mAT-125H perfekt und wird bei einer nächsten POTA Aktivierung eingesetzt. Schön hat der mAT-125H nun doch noch einen Platz in einem Setup gefunden. (PS: Ich mag Setups, ich packe dann immer alles was dazu gehört in einen Kiste damit alles bereit ist) So habe ich nun ein IC-705 ein Xiegu-G90 und ein Kenwood TS-480 Setup am Start.

TS-480HX mAT-125H

Kenwood TS-480HX MARS MOD

  1. Turn off the transceiver and disconnect the antenna and DC supply.
  2. Remove the top panel (8 screws).
  3. Remove 4 screws from the shield plate and then remove the plate to access the TXRX (A/2) board (this shield plate is toward the front of the radio and only has 4 screws). Be careful to avoid damaging the wiring and coax cables that cross over the top of the shield plate.
  4. After doing step above face front of radio toward you. Underneath the plate you just removed you will see two large IC’s. The one on the left has labeling saying “DSP”. Just between these two large IC’s is a resistor clearly labeled R321 (which is a large resistor mounted vertically). On resistor R321 you will notice that one of the leads attaches to circuit board then loops over to another pad on the circuit board, where it is connected. If you draw an imaginary line between the center of the leads of R321, going to the right toward the large IC on the right you will see one single surface mount resistor. If you have a magnifying glass it is labeled 102. This is R221 and the one you want to remove.. On either side of R221 are open pads (USA version).
  5. Locate and carefully remove resistor R221 from the TX-RX board.
  6. NOTE to our European hams: You may also see resistors in the 0, 1, 2, and/or 3 positions. In order to be able to operate in the full portion of 40M, remove any resistors in 0, 1, 2 or 3 positions. This would be in addition to removal of R221. You may wish NOT to remove R221 however, and you will still have TX above 7.100 Mhz. hanks to Hans, DJ6TJ for trying this out!
  7. Replace the shield plate removed in step 3. Take care not to pinch any wires in front of the shield. Replace the covers. It will automatically reset when turned on. Transmitter Frequency Range: 1.700 – 30MHz, and 49.00 – 54MHz (R221)
  8. Transmitter Frequency Range: Ham bands, plus 7.100-7.300 Mhz (0, 1, 2, 3)

© 2024

Theme by Anders NorenUp ↑