Heute war ein guter Tag meinen Kelemen Dipol DP-8040201510, den ich Occasion kaufen konnte, etwas ausführlicher zu testen: Respektive die Resonanzpunkte zu messen und ev. noch etwas abzustimmen. In der Vergangenheit hatte ich immer das Problem keinen Mast vorrätig zu haben an dem ich eine “schwerere” Antenne hochziehen kann. Ein GFK Mast versagt da kläglich und wird in Sekunden zu einer Banane… . Was tut man da? Man bestellt sich einen tollen Aluminium Schiebemast 12m, Transportlänge bis 1.5m bei WIMO (oder sonst wo).
Der Aufbau im Garten ging damit ruckzuck.. einzig die schrauberei kann noch mit Schnellspanner f. Portabelmaste optimiert werden. Leider gibt es diese beim oben genannten Lieferanten nur als M8-Schrauben Version. Mein Mast benötigt aber M13 Schrauben… Falls jemand eine Idee hat wie das gelöst werden kann, ich bin offen für Ideen. Zurück zum Thema…
Kelemen-Antennen zeichnen sich durch grosse Bandbreite, hohen Wirkungsgrad, geringes Gewicht, Wetter- und Temperaturbeständigkeit sowie 50-Ohm-Speisung aus. Kelemen-Antennen sind Drahtantennen mit Sperrkreisen aus teflonisoliertem Koaxkabel. Kelemen Dipole zeichnen sich weiter durch geringes Gewicht bei einer guten Stabilität aus. Erreicht wird dies durch Verwendung von leichtem Teflonkabel für Traps und Verlängerungsspulen. Der Balun ist absichtlich nicht wasserdicht verschlossen um Gewicht zu sparen (?!). Die Antenne stehen als Monoband und Multiband Dipole zur Verfügung, des Weiteren in verschiedenen Leistungsklassen.
Ich war ja schon etwas gespannt auf die erste Messung über alle Bänder :
Auf 80m muss noch etwas abgestimmt werden, die Schenkel sind im Aufbau als Inverted V etwas zu lang. Kein Problem das zu erledigen, einfach die äusseren Enden etwas umschlagen und die Länge dadurch kürzen.
Das 15m Band dürfte etwas längere Schenkellängen haben, das nachträglich anzupassen wird eher schwierig. Es müssten nochmals alle nachfolgenden Längen verändert werden… zu viel Aufwand. Da muss dann halt der Tuner etwas nacharbeiten…
10m 20m und 40m passen perfekt… eine tolle Antenne die auch mal etwas Leistung (max 2Kw PEP) verträgt wenn man das mal benötigt. Meist reicht aber ja wenig Leistung wenn die Antenne effizient ist und die Bedingungen für das Band passen.
Da freue ich mich doch die Antenne beim nächsten Field Day einzusetzen, im Garten ein paar QSO zu arbeiten ist immer toll, der Einsatz bei einem Field Day aber dann doch etwas anderes.
Gestern veranstaltete der Verein Hobby Funker Innerschweiz HB9GF Ihren jährlichen legendären Grill und Praxistag in Dogelzwil. Es war wirklich ein sehr interessanter und toller Nachmittag den ich dort verbrachte. Sensationell endlich mal das Contest Fahrzeug live zu sehen. Wir haben viele interessante Gespräche geführt, Neuigkeiten ausgetauscht und natürlich grilliert. Ein super organisierter Anlass mit vielen netten OM’s… Ich kann jedem der einen Verein sucht die Hobby Funker Innerschweiz empfehlen, die tun sehr viel für das Funken, für die Funker….
Mit grosser Freude ist mein Paket mit dem JC-4s Stockcorner bei mir angekommen.
Stockcorner JC-4sStockcorner JC-4s
Bereits in der Vergangenheit habe ich einen Stockcorner Modell JC-3s den ich dankender weiser damals von Markus HB9EIZ übernehmen konnte eingesetzt. Der JC-3s hat ausnahmslos einen guten Dienst gemacht. Der JC-3s kann mit 200 Watt belastet werden, inzwischen steht bei mir im Shack eine sps Expert 1.3 und wartet darauf etwas mehr Leistung an die Antenne zu übergeben. Der JC-4s verträgt problemlos 1000 Watt, was im HB Land dann eh das Maximum ist was man darf.
Nach einem kurzen Test auf dem Gartentisch der absolut problemlos verlief, stand der Montage am Mast nichts mehr im Wege.
Stockcorner JC-4s
Inzwischen ist der JC-3s am Mast getauscht und der JC-4s montiert. Angeschlossen ein 48m langer Draht in ca.15m Höhe, als endgespeiste Drahtantenne. Als Gegengewicht (counterbalance) habe ich diverse Radiale in verschiedenen Längen in alle Richtungen verlegt, der längste hat eine Länge von ca. 80m. Wie erwartet kann ich auf allen KW Bändern (10 bis 160m) ohne Probleme tunen.
Einige Verbindungen auf verschiedenen Bändern habe ich bereits mit dem neuen Tuner geloggt…
HB9HJI
Wirklich ein hervorragendes Produkt was ich jedem sehr empfehlen kann.
Nachdem mich die kürzlich gebaute 6m Deltaloop immer noch begeistert, dachte ich mir an diesem schönen Sonntag heute mal eine Deltaloop für das 15m Band zu bauen. Ausser den Drahtlängen ist es die selbe Antenne, da der obere horizontale Schenkel 378cm lang wird habe ich 3 Stück Elektrohre verwendet die ich zusammenschieben kann.
Längen für 15m Band DeltaloopTransportgrösse Deltaloop 15m Band
Da ich die Drähte immer etwas länger als die geplante Länge konfektioniere, musste ich zwei, drei Mal kürzen bis ich das SWR an der richten Stelle hatte. (Abschneiden geht immer )
SWR Deltaloop 15m Antenne
Leider hatten wir heute sehr starken Wind, so konnte ich die Antenne nicht auf die gewünschte Höhe ziehen. Für das anpassen des SWR und einen ersten Test reicht die Höhe aber gut.
Deltaloop 15m Band in der Luft
So jetzt warte ich auf das nächste Sporadic Fenster im 15m Band dann kann es los gehen mit DXen.
Kontrollgruppe: Rapport (RS oder RST) un Standort-Kanton (z.B: 59 ZH oder 599 ZH)
Nächste Durchführung: 5. Dezember 2020 SSB: 07:00 – 09:59 UTC Digital: 10:00 – 10:59 UTC
Seit Wochen habe ich mich auf dieses Wochenende gefreut, konnte ich doch meine Contestskills testen und verbessern. Ich habe auch einiges im Vorfeld unternommen um mich vorzubereiten.
Mein Setup hat wie folgt ausgesehen:
Transceiver IC-7300
Endgespeiste Drahtantenne an einem JC-3s Stockcorner
Heil Pro Elite mit Fusstaster
ContestConsole von Sotabeams
UcxLog Software
Zwei Dinge in meinem Contestsetup sollen besonders erwähnt werden. Einmal habe ich mir die ContestConsole von Sotabeams gekauft. Diese ermöglicht die im IC-7300 gespeicherten Records über Tastendruck abzurufen. Der Komfort CQ zu rufen hat sich damit erheblich erhöht. Ein neues Teil in meinem Shack das ich in Contests nicht mehr missen will.
ContestConsole Sotabeams HB3XUC
Der zweite im für mich fast wichtigere Punkt, ist die Logsoftware UcxLog. Die letzen Contestversuche habe ich mit MacLoggerDX als Logsoftware durchgeführt. MacLoggerDX ist unbestritten die beste Logsoftware für Applegeräte. Die Bedienung ist einfach, übersichtlich und modern. Die Software hat alle Funktionen, die im normalen DX Gebrauch benötigt werden und stellt alle Schnittstelle zu QRZ.com, LoTW Logbook of the World usw zu Verfügung. Die integrierte Contestfunktion lässt jedoch einige Funktionen vermissen. Auf anraten von befreundeten OM’s und meines Clubs dem HB9TG ,habe ich mir UcxLog heruntergeladen und leider Gottes auf einem Windowsrechner installiert (ich liebe mein MacBook ). Nach einigen Tests vor dem Contest, musste ich sagen UcxLog bietet sehr viele tolle Funktionen für einen Contest. Das Programm selbst sieht im Design etwas von gestern aus, die einfache Bedienung und die sehr umfangreichen Features machen das problemlos wett. Ein Programm für einen Contest muss funktionieren und soll keinen Designerpreis gewinnen.
Das Programm kennt alle gängigen Contest (diese werden durch Updates aktualisiert) und stellt damit die passenden und benötigten Eingabefelder des Contests zu verfügung. Viele zusätzliche Fenster können angezeigt werden, ich habe mir das 80m Band mit der Anzeige der für den Contest relevanten Stationen die gespottet wurden eingeblendet. Ein sehr tolles Hilfsmittel will man über das Band drehen um Multiplikatoren zu loggen. Dabei werden die noch nicht geloggten Stationen farblich zu den geloggten unterschieden. Weiter sind diverse Ansichten in Fenstern möglich, Cluster, Multis und und und. Eine ausführliche Beschreibung der Software würde meine Webseite sprengen. Das Programm hat mich in diesem Contest von Anfang bis Ende überzeugt. Gerne bezahle ich den kleinen Betrag für die Lizenzierung der nächsten zwei Jahre. Für den Contest habe ich die Demoversion verwendet, es sind keine Einschränken in der 60 Tagen Version vorhanden.
UcxLog mitten im ContestContest Station HB3XUC
Jetzt bin ich natürlich sehr gespannt an welcher Stelle ich in der Rangliste auftauchen werde….
Ein grosses Danke an alle OM’s die an dem Contest teilgenommen oder Punkte verteilt haben. Der Contest lebt von den Stationen in dem Zeitfenster in der Luft sind.
Wieder ist ein interessantes Wochenende Geschichte, der Scandinavian Activity Contest war ganz spannend. Sehr viele OM’s aus den skandinavischen Ländern waren auf 3,5 bis 28 MHz (ohne WARC) zu hören.
Viele Stationen konnte ich erreichen und in mein LOG eintragen, hier eine Aufzeichnung wie es an einem Contest klingt:
Hier ein Auszug der Regeln:
Rules
Scandinavian Activity Contest Rules 2020
Rules for all participants
Latest update 2020-09-01: Clarified 4.1 and added info about “scattered stations” in 4.4.
Changes compared with 2019 are marked with red text.
1. Aim of the contest
The aims of the contest are to promote amateur radio activity in Scandinavia and to encourage amateur radio communications between Scandinavian and non-Scandinavian amateur radio stations. Scandinavian stations will try to work as many non-Scandinavian stations as possible and vice versa.
Scandinavian stations are defined by prefixes as follows:
Svalbard and Bear Island JW Jan Mayen JX Norway LA – LB – LC – LG – LI – LJ – LN Finland OF – OG – OH – OI Aland Islands OFØ – OGØ – OHØ Market Reef OJØ Greenland OX – XP Faroe Islands OW – OY Denmark 5P – 5Q – OU – OV – OZ Sweden 7S – 8S – SA – SB – SC – SD – SE – SF – SG – SH – SI – SJ – SK – SL – SM Iceland TF
All other legal prefixes according to the ITU definition of Scandinavian prefixes are good for the contest and multipliers as well. Greenland is included as a Scandinavian prefix, although it is located in North America.
2. Eligible entrants
Licensed radio amateurs all over the world are invited to participate.
3. Periods
CW: 3rd full weekend of September each year. SSB: 2nd full weekend of October each year.
Starts 12:00 UTC Saturday and ends 11:59 UTC Sunday.
4. Entry Categories
Scandinavian and non-Scandinavian stations are placed in separate categories.
4.1 Single Operator – Single TX
Single operator means that one single person performs all operating, logging and spotting functions.
4.1.1 For Scandinavian stations:
All Band – High Power [SINGLE-OP ALL HIGH]
All Band – Low Power (transmitter output 100 W or less) [SINGLE-OP ALL LOW]
All Band – QRP (transmitter output 5 W or less) [SINGLE-OP ALL QRP]
Single Band [SINGLE-OP 80M] [SINGLE-OP 40M] [SINGLE-OP 20M] [SINGLE-OP 15M] [SINGLE-OP 10M]
All Band, Single Operator entrants may also participate in one of the overlay categories by adding the CATEGORY-OVERLAY: line with either ROOKIE, TB-WIRES or WIRE-ONLY in their Cabrillo log file:
Participants in the ROOKIE overlay must be licensed for the first time less than 3 years before the actual contest starts.
Participants in the TB-WIRES overlay shall use only one triband antenna with a single feed line from the transmitter to the antenna for 10, 15 and 20 meters, and single-element antennas for 40 and 80 meters.
Participants in the WIRE-ONLY overlay shall use the same single wire antenna for all bands.
Overlay category entries will be listed separately in the results. They are scored as All Band entries and grouped by High Power and Low Power (includes QRP).
4.1.2 For non-Scandinavian stations:
All Band – High Power [SINGLE-OP ALL HIGH]
All Band – Low Power (transmitter output 100 W or less) [SINGLE-OP ALL LOW]
All Band – QRP (transmitter output 5 W or less) [SINGLE-OP ALL QRP]
Low Band – High Power, only 80 and 40 meters. [SINGLE-OP LOW-BAND HIGH]
4.2 Multi Operator – Single TX – All Band [MULTI-ONE]
This category is for all participants. Only one signal may be transmitted on any band at any time (running station). When operation has started on one band, the station must remain on that band for at least 10 minutes. The 10-minute period starts with the first QSO worked on that band.
Exception: It is allowed to work a QSO on another band if it is a new multiplier (multiplier station). The multiplier station is allowed to be on the air at the same time as the running station. The multiplier station may not solicit contacts by calling CQ, but may ask stations during the multiplier QSO to move to another band where the multiplier is needed. The log must indicate which station/signal (run or multiplier) made each QSO.
4.3 Multi Operator – Multi TX – All Band [MULTI-MULTI]
This category is only for Scandinavian stations. There are no restrictions on the number of transmitters. Only one signal per band is allowed at any time.
4.4 Station Location
All transmitters and receivers must be within a single 500-meter diameter circle. Antennas must be physically connected by RF transmission lines to the transmitters and receivers.
Exception for 2020: Due to the Covid-19 pandemic we allow Scandinavian Multi-Multi stations to operate with “scattered stations”, similar to the HQ-station concept in the IARU HF Championship. If you decide to participate with “scattered stations”, please inform us via email to support@sactest.net.
4.5 QSO finding assistance
The use of DX-Cluster, Skimmer, and Skimmer-like technology (such as Reverse Beacon Network) is allowed for all categories. Self-spotting or requesting stations to announce one’s own call on the DX-Cluster is NOT allowed.
5. Frequencies to be used
CW : 3510-3560, 7000-7040, 14000-14060, 21000-21070, 28000-28070 kHz SSB: 3600-3650, 3700-3800, 7060-7100, 7130-7200, 14125-14300, 21151-21450, 28320-29000 kHz. According to the IARU Region 1 HF Bandplan.
6. Contest exchanges
The contest exchange consists of RS(T) plus serial number sequence starting with 001 (e.g., 59(9) 001). QSO’s after 999 are numbered 1000, 1001, etc. Stations in the Multi Operator Single TX category may use separate serial number sequences on each band. Stations in the Multi Operator Multi TX category must use separate serial number sequences on each band. The same station may be worked once on each band. Cross-mode and/or cross-band QSO’s are not allowed. The minimum content of a valid contest QSO is a correct callsign and correct contest exchanges.
If the station worked does not send a serial number, log the contact with number 000. QSO’s with zero in the received serial number field will not give QSO points nor multiplier points. Do not enter a “fake” number if you log a station that doesn’t send a serial number. QSO’s that we find with “fake” numbers will be lost, and may also lead to further penalties.
7. Scoring
A QSO with correct callsign and received exchange counts for QSO points. QSO’s with stations that do not give the required contest exchange do not count for QSO points or multipliers.
7.1 For Scandinavian stations:
EUROPEAN stations, outside Scandinavia, are worth two (2) points for every complete QSO.
NON-EUROPEAN stations are worth three (3) points for every complete QSO.
7.2 For non-Scandinavian stations:
EUROPEAN stations receive one (1) point for every complete Scandinavian QSO.
NON-EUROPEAN stations receive one (1) point for every complete Scandinavian QSO on 14, 21, and 28 MHz and three (3) points for every complete QSO on 3.5 and 7 MHz.
8. Multipliers 8.1 For Scandinavian stations:
Each worked non-Scandinavian DXCC entity is valid for one multiplier for each band.
8.2 For non-Scandinavian stations:
Each worked prefix-number (Ø-9) in each Scandinavian DXCC entity is valid for one multiplier for each band (e.g. SI3, SK3, SL3, SM3, 7S3, and 8S3 are all in ONE district and count for ONE (1) multiplier on each band). Stations without a prefix number count for the 10th area (e.g., LA/G3XYZ counts for LAØ), and those with two or more prefix numbers counts for the area indicated by the first number (e.g., OZ150A counts for OZ1).
9. Final score
To calculate the final score, multiply the sum of QSO points on all bands with the sum of multipliers worked on all bands.
10. Logs
Logs must be submitted separately for CW and SSB, and the QSO’s must be listed in chronological order. By submitting a log, you agree that your log and the corresponding log checking report may be made open to the public. Electronic submission of logs at https://www.sactest.net is required for all entrants. Use the CABRILLO format. Please ensure that you fill out all of the header information, including a possible category overlay as indicated in §4 above. Leave all your QSOs in the log, dupes included. The log checking software will find the dupes and mark them with zero points. Participants aiming for a top-three score should include the exact frequency (a 1-kHz resolution is sufficient) of every contact in the log.
11. Closing date for logs
Cabrillo logs or typed-in paper logs shall be uploaded no later than 5 days, at 23:59UTC after the end of the contest. Logs submitted after the deadline will be listed as checklogs.
12. Awards
Certificates for all participants will be downloadable for printout from the SAC website.
12.1 Plaques
Contest plaques in both CW and SSB part will be given to the following.
Scandinavian winner stations:
All Band categories: High Power, Low Power and QRP.
Overlays: Rookie, TB-Wires and Wire-only no matter of transmitter power used.
Multi-One and Multi-Multi.
Non-Scandinavian winner stations:
All Band, Low-band and Multi-One from each continent. No matter the power used, but there must be at least 25 QSOs in the log.
Depending on the number of participants, the Contest Committee may consider additional awards.
12.2 Sponsored Plaques
Both Scandinavian and non-Scandinavian stations may receive Special Plaques sponsored by individuals through the “SAC Sponsored Plaque Program”. Find more information on www.sactest.net
13. Scandinavian Cup
The Scandinavian Cup is a competition between the Scandinavian Regions as defined in §1. All entrants’ scores for both CW and SSB are accumulated to a total for each region. All logs, except for checklogs, are counted towards the total. A circulating trophy is awarded to the national society of the region that wins the Cup.
14. Judging
Violation of Amateur Radio Regulations in the country of the entrant or the rules of this contest, unsportsmanlike conduct, and taking credit for unverifiable QSO’s or multipliers may lead to disqualification. The decisions by the Contest Committee are final and definite. The right to changes in these rules is reserved.
15. Organizer
The Nordic Radio Amateur Union (NRAU) is the organizer of the contest. The member societies of NRAU are EDR (Denmark), FRA (Faroe Islands), IRA (Iceland), NRRL (Norway), SRAL (Finland), and SSA (Sweden).
The contest is administered by a committee composed of one member each from Denmark, Finland, Norway, and Sweden.
Heute lies es das Wetter einigermassen zu, dass ich die Antenne nochmals im Garten installieren und abstimmen konnte. Das erreichte SWR auf den Bändern 10m 15m 20m 40m und 80m kann locker mit einem Tuner noch angepasst werden. Für eine zuverlässige Funkübertragung muss die Antenne abgestimmt und an die Elektronik des Transceivers angepasst werden.
Hier eine Übersicht über alle Bänder:
SWR end Fed Antenne 1:64 / HB3XUCSWR end Fed Antenne 1:64 / HB3XUC
Das 80m Band ist durch die Verlängerungsspule etwas schmalbandig, ich habe die Länge gekürzt damit die Antenne in etwa auf 3.700 ein optimales SWR zeigt. 3.700 ist unsere “Hausfrequenz” auf der wir uns regelmässig am Abend um 21.00 Uhr für eine QSO Runde treffen.
SWR end Fed Antenne 1:64 80m Band/ HB3XUCSWR end Fed Antenne 1:64 80m Band/ HB3XUC
Hier noch das SWR der anderen Bänder:
SWR end Fed Antenne 1:64 10m Band/ HB3XUCSWR end Fed Antenne 1:64 15m Band/ HB3XUCSWR end Fed Antenne 1:64 20m Band/ HB3XUCSWR end Fed Antenne 1:64 40m Band/ HB3XUC
Damit ist das Projekt im Moment abgeschlossen, sobald das Wetter es zulässt werde ich die Antenne aufbauen und freue mich auf viele QSO’s.
Gestern habe ich das nächste Teil meiner end fed Antenne mit dem 1:64 Balun fertig gestellt. Es handelt sich um die Spule die ich in die Antenne einsetzen will. Natürlich habe die Konstruktion nicht selbst erfunden sondern nehme die Anleitung von einer Webseite im Internet, hier der Link.
End-Fed Antenne
Da ich kein passendes Kunstoffrohr im Sammelsurium gefunden habe, habe ich einen anderen Durchmesser verwendet. Mein Rohr für die Spule hat einen Durchmesser von 50mm gewickelt mit einem 1,2mm Kupferlackdraht. Um auf die 110uH zu erreichen habe ich folgende Formel für die Berechnung herangezogen:
Meine Spule sieht dann in etwas so aus, nicht das schönste Stück aber es ist sicherlich funktionell.
110uH
Um auf die 100uH mit meinem Kunstoffrohr mit 50mm Durchmesser, habe ich 68 Windungen 1.2mm Kupferlackdraht aufgebracht. Berechnen kann man das mit diversen Onlinerechnern, ich habe folgenden von DF7SX verwendet: http://www.df7sx.de/luftspule/